Drinking Water Flow Control and Measurement Application Notes

31. Capital Controls Series 480 Vacuum Gas Feeders 10/8/2015

    The Capital Controls Series 480 all-vacuum gas feeder is designed for direct mounting to a 150 pound gas cylinder or ton container. It is a basic alternative for those applications requiring a chlorine feed rate of 250 PPD (5 kg/h) or less. 

32. SITRANS LR100 4/27/2023

    Liquid, slurry, or solids measurements? Dirty applications? These maintenance-free sensors deliver the reliable performance you need, no matter what the environment.

33. OPTIMASS 3400 Coriolis Mass Flowmeter 9/16/2019

    The OPTIMASS 3400 is a cost-effective Coriolis mass flowmeter for accurate flow measurement of liquids and gases in a variety of demanding low flow and dosing applications (from 0.3 kg/h or 0.01 lb/min upwards). The OPTIMASS 3400 features Entrained Gas Management (EGM^TM) for liquid applications, providing reliable readings even in the event of gas entrainment of up to 100%. In this way, the Coriolis meter enables continuous and uninterrupted measurement of volume flow and mass, density and temperature –  even at very difficult process conditions with 2-phase flow.

34. OPTIMASS 6400 Coriolis Mass Flowmeter 9/9/2019

    The OPTIMASS 6400 is the standard high performance Coriolis mass flowmeter for the process industry. The twin bent tube meter offers superior performance and high accuracy in virtually any application: From process control in (petro)chemical applications to concentration measurements in the food and beverage industry to custody transfer filling and transport measurements in the oil and gas industry. Its high-end options also make the OPTIMASS 6400 the optimum device for cryogenic media like Liquefied Natural Gas (LNG) with temperatures down to -200°C / -328°F as well as applications involving high operating temperatures (up to 400°C / 752°F) or pressures (up to 200 barg / 2900 psig).

35. QCT Series In-Line Ultrasonic Flow Meters for Low Viscosity Liquid Applications 11/29/2019

    The compact QCT Series has no moving parts and there is nothing in the flow stream that will cause an increase in pressure drop; this results in a very rugged, reliable and accurate flow meter. High accuracy & repeatability is achieved through the unique measurement section within the flow meter where the flow is conditioned and delta T is measured along the axis of the flow meter. The small footprint, lightweight device is ideal for low viscosity liquid applications including water, water-based products, oils, and its all plastic construction makes it the meter of choice for many corrosive fluids.

36. FLUXUS F601 Portable Flowmeter 12/9/2014

    The FLUXUS F601 is the portable clamp-on flow meter of choice for servicing and maintenance activities, the control and auditing of measurement points not covered by permanent meters, or even the temporary replacement of permanently installed flow meters.

37. FLUXUS ADM 5107 Water Flowmeter 12/9/2014

    The FLUXUS ADM 5107 is FLEXIM's solution for many flow metering applications found in the water and wastewater sector and adjacent industries. As FLEXIMs basic and economic alternative, the ADM 5107 offers the same benefits in terms of accuracy and reliability as its bigger brothers, the FLUXUS ADM 7407 and ADM 8027.

38. Complete Flow Solutions 11/11/2024

    Siemens’ extensive portfolio includes various flow measurement technologies, such as Coriolis, clamp-on ultrasonic, vortex, and differential pressure meters, catering to a wide range of industrial needs.

39. Capital Controls® Gas Feeder Series WM4000 10/12/2015

    Capital Controls Series WM4000 gas feeders are wall cabinet mounted vacuum operated and designed to conveniently house a combination of gas feed equipment. The fibreglass cabinets enclose the gas flow control components.

40. AFC SEMPER™ Remote Pressure Monitor (RPM) With Impulse Technology 2/18/2020

    The AFC SEMPER® RPM featuring "Lift & Shift" capability is an ideal solution for pressure monitoring, transient analysis, fire flow testing, customer pressure concerns, and hydraulic model calibration. This flexible installation method allows the use of a smaller number of units to cover a large area with the advantage allowing utilities to move their RTU’s quickly and easily without having to reconfigure the application or retrofit existing assets.