White Papers and Case Studies For The Power Generation Industry

  1. Manipulating Dissolved Gasses With SEPAREL®: Power Generation
    2/28/2018

    In the power generation industry, water quality is specified by boiler and turbine manufacturers. The removal of dissolved ions and dissolved gasses, such as oxygen and carbon dioxide, must be reduced to extremely low concentrations long before the water enters boilers for steam production.

  2. Compressor Installation Lowers Energy Needs By 18%
    8/7/2014

    RWE uses three-low pressure centrifugal compressors from Atlas Copco in the Ibbenbüren power plant to generate oxidation air for the flue gas desulphurization installation.

  3. 3 Tips To Optimize Cooling Water Management For Lower Plant Operating Costs
    6/12/2015
    The proper control and treatment of cooling water is essential for efficient, safe, and economical operations. Chemicals are fed to these systems that protect against fouling, corrosion, and microbiological contamination. The proper dosage of these key chemicals is determined by having accurate information on the system make-up and blowdown water.
  4. Creating Stability For The Energy Revolution Takes Ability
    8/6/2018

    ABB provides an extensive selection of proven measurement and analytical products and solutions for power generation industry applications.

  5. Power Plant Uses 3M Liqui-Cel Membrane Contactors To Remove CO2 From Water
    6/21/2017

    A major power plant in Thailand is using 3M™ Liqui-Cel™ Membrane Contactors to remove carbon dioxide from a DI water system. The system is an expansion project and will be used to feed a high pressure boiler. Liqui-Cel membrane contactors are being used to lower the CO₂ inlet into an Ionpure Electrodeionization (EDI) system. Carbon dioxide adds an ionic load to the EDI system, which can reduce the performance of the system. Manufactures of the EDI equipment suggest lowering the inlet CO₂ to reduce the load on the equipment and improve the water quality.

  6. Seawater Treatment Yields Process Water For Power Plant
    10/27/2017

    A power plant in Egypt needed to use seawater from the nearby Red Sea as feed water for its plant processes. This case study shows how Fluence designed and built a new seawater demineralization plant that includes an ultrafiltration pretreatment, reverse osmosis, and mixed bed ion exchange.

  7. Maximum Water Reuse, Zero Liquid Discharge — A Power Plant Case Study
    3/1/2015

    ELCOGAS, established in 1992 with the aim of building and operating a 335 MW Integrated Gasification Combined Cycle (IGCC) power plant as well as the commercialization of its technology.

  8. Rokeby Generating Station Saves 50% In Capital Expense By Using 3M™ Liqui-Cel™ EXF-14x28 Series Membrane Contactors To Remove CO₂ To Extend Mixed Bed Resin Life
    8/10/2017

    Lincoln Electric Systems (LES) recently commissioned a membrane decarbonation system using  3M™ Liqui-Cel™ EXF-14x28 Series Membrane Contactors to remove CO2 prior to their mixed bed deionizers.

  9. Developments In Heat Transfer Technology Can Improve Exchanger Efficiency And Reduce Water Demand
    2/28/2014

    Water’s high heat capacity, high thermal conductivity, and historically low cost make it popular for process heat exchange. Power plants, especially those for liquid cooling applications, withdraw a large fraction of the total demand for water necessary for agriculture, industry, recreation, hygiene, drinking, and wildlife.  By Kevin J. Farrell and Vijay Sathyamurthi, Heat Transfer Research, Inc., College Station, Texas USA

  10. Building An Invisible And Soundless Power Plant
    6/23/2017

    The Villoresi Channel, located north of Milan, was designed with the main purpose of agricultural irrigation while providing water to the city of Milan. The paths running along the canal were also used for recreational purposes and cross through some of the most beautiful natural parks in Lombardy.